For porcelain tile and natural stone
Standard : ANSI A118.6 (Unsanded), A118.7 (Unsanded)
Colors : 8 colors
Packing : 0.5 Kg./bag
Remark All product images shown may vary due to differences in monitors.
ภาพและสีที่แสดงบนเว็บไซต์อาจมี ความแตกต่างจากสินค้าจริง เนื่องจากการตั้งค่าแสดงผล ของแต่ละหน้าจอ
Crocodile Turbo Plus is a very fine grout with high fluidity, but it is highly compression-resistant, anti-black mold, and reduces efflorescence. This product is perfect for very narrow joint and can be applied to porcelain tiles, marble, granite. It has high adhesion and scratch resistance and can be used in any area, indoors or outdoors, that requires high resistance, such as swimming pools, parking lots, saunas, bathroom, washing area, etc.
Crocodile Turbo Plus is a special formula tile grout made from special cement and additives which helps increase followability. It provides high compressive strength, firmness and durability. Perfect for porcelain tile, marble, granite with rectified edge and tile for specific area that requires high resistance ex. Swimming pool, garage, sauna ,…etc.
Installation
Joint width should be between 0.2-5 mm and depth should not be less than 2/3 of tile thickness. Recommend to apply tile grout 48 hours after tile installation.
Preparation
Clean and remove any dirt or contaminations remaining in the joints. Make sure the joints are clean and dry before grouting.
Mixing ratio
Floor
Joint width 0.2-1 mm :
Mix 0.5 kg of grout powder with 0.165 L of clean water, or 3 parts grout to 1 part water (by volume)
Joint width 2-5 mm :
Mix 0.5 kg of grout powder with 0.15 L of clean water, or 3.5 parts grout to 1 part water (by volume)
Wall
Joint width 0.2-1 mm :
Mix 0.5 kg of grout powder with 0.15 L of clean water, or 3.5 parts grout to 1 part water (by volume)
Joint width 2-5 mm :
Mix 0.5 kg of grout powder with 0.14 L of clean water, or 3.8 parts grout to 1 part water (by volume)
Mixing
• Add the grout into water and mix with low speed drill.
• Recommend to use within 20 mins (pot life)
• Discard grout when too stiff to work, do not add more water to prolong usage
Application
1. Fill the joints with well mixed grout, then using a rubber face trowel diagonally across the grout joints.
2. Remove all excess grout with the trowel and leave until curing. Clean tile surfaces with wet sponge and clean cloth.
Curing
Care should be taken within 6 hours to prevent the grout from drying out or dirt by covering the installation with natural Kraft paper (Plastic or newspaper sheet should not be used).
Final Clean-Up
2 days after grouting the area should be cleaned to remove any remaining grout from the tile surface. Soaking soap and warm water into the floor and leaving for a while before wiping. It is not recommended to use acids as they cause grout peeling or color alteration
• If necessary, use diluted acid or Crocodile Grout Cleaner. Test in an inconspicuous place first.
• Any glossy coating or special scrubbing should be applied after the grout has completely cured in 30 days. Test in an inconspicuous place first.
Caution
• Not recommended to use in the area exposed to acid all the time.
• May be harmful to the eyes, skin, or lungs. Wear suitable protective clothing, gloves, and eye/face protection.
• In case of contact with eyes, rinse immediately with water and seek medical advice.
• After contact with skin, wash immediately with water.
• Keep out of reach of children.
Storage
• Lasts up to one year if kept dry and away from heat, in a sealed bag.
• Use within 1 year from the date of manufacturing.
Packing
Net weight : 0.5 kg / bag